AMX Stereo Receiver UDM RX02 User Manual

Quick Start Guide  
UDM-RX02 Endeleo Multi-Format Receiver  
Configuration  
Overview  
The UDM-RX02 is configured via the UDM Hub’s WebConsole. Refer to the UDM  
Installed at the display device, the UDM-RX02 (FG-UDM-RX02) converts the signal  
received from a UDM Multi-Format Distribution Hub to standard A/V signals (FIG. 1).  
Hub’s Operation/Reference Guide for details.  
Rear Panel Components  
All of the connectors and ports are located on the rear panel (FIG. 2):  
Composite (Pr) port  
Composite (Pb) port  
Composite (Y) port  
UDM HUB port (RJ45) - from an  
“OUTPUT” port on the UDM-0102  
VGA (HD15) port  
S-Video port  
CVBS port  
Serial port (RJ12)  
FIG. 1 UDM-RX02  
With all the same features of the UDM-RX01, the UDM-RX02 adds support for  
“Common” mode sync, as well as remote power for long cable distance runs.  
Compatibility  
The UDM-RX02 is compatible for use with the following UDM Hubs:  
IR Rx port  
IR Tx port  
RCA audio  
UDM-0102 (FG-UDM-0102) - This hub supports Common Synch Mode.  
UDM-0404 (FG-UDM-0404) - This hub supports Common Synch Mode.  
UDM-1604 (FG-UDM-1604C) - This hub supports Common Synch Mode.  
UDM-1604 (FG-UDM-1604) - This hub does not support Common Synch Mode.  
In this case, the UDM-RX02 will function, but without Common Synch Mode.  
(left/right)  
Power connector  
SPDIF female Digital Audio port  
FIG. 2 UDM-RX02 - rear panel components  
UDM Hub Port (RJ45)  
The UDM-RX02 connects to a UDM Hub through a Cat 5/Cat 6 connection. Refer to  
the UDM Hub’s Operation/Reference Guide for details.  
Product Specifications  
UDM-RX02 Specifications  
Serial Port  
Power Requirements:  
24VDC @ .75A  
The Serial port is available for diagnostic and troubleshooting purposes.  
The Serial port on the UDM-RX02 is an RJ12 connector, and requires a DB9-to-RJ12  
adapter cable (FG-RS01) to connect to a PC for Terminal control.  
Note: In most cases the UDM-RX02 is remotely powered  
by the UDM Multi-Format Distribution Hub (see Powering  
IR Receiver (IR Rx) Port  
Rear Panel Connectors:  
The IR Rx port is used to enable user control and the remote compensation of the  
video link to the UDM, using the FG-UDM-RC10 and the FG-IR03.  
Power Socket:  
2.1mm barrel-style DC power socket (female)  
UDM Hub (RJ45)  
Port:  
Provides audio/video transport as well as control via Cat5,  
Cat5e or Cat6 to an UDM Hub.  
Refer to the Protocols and IR Learning section of the UDM Hub’s Operation/Reference  
Guide for details for information on learning a device’s IR commands.  
Serial (RJ12) port:  
Enables an administrator to control the various functions  
to the UDM-RX02 from a command line prompt and termi-  
nal connection.  
IR Transmit (IR Tx) Port  
The IR Tx port issues IR commands from the UDM-RX02 to a controlled display  
device (TV monitor or display). One IR display device can be connected to the UDM-  
RX02 via the IR Tx port, and controlled via the UDM Hub’s WebConsole or via remote  
control.  
• Requires a DB9-to-RJ12 adapter cable (FG-RS01) to  
connect to a PC.  
• 9600, 8 bit, No Parity, 1 Stop Bit  
Connecting an IR Device to the IR Tx Port  
1.  
Connect an IR01 Endeleo IR Emitter Module (FG-IR01) to the IR Tx port on the  
UDM-RX02.  
IR Rx Port:  
3.5mm stereo input port, for connection of an IR receiver  
to allow setup of the UDM-RX02, local compensation  
controls, and remote control of centrally located IR  
devices.  
Note: Ensure the position of the device corresponds to the position assigned in  
the Devices option of the UDM- Hub’s WebConsole.  
Run the other end of the IR Emitter cable to the device’s IR sensor, and attach  
the IR Emitter to the device’s sensor by removing the cover on the reverse side  
of the IR Emitter.  
2.  
IR Tx Port:  
3.5mm stereo IR Transmitter output port allows one IR-  
controlled device (such as a DVD or VCR player) to be  
controlled via optional wired IR emitter.  
IR commands for each device on the system have to be learned by the UDM-0102 in  
order to function properly. Refer to the Protocols and IR Learning section of the UDM  
Hub’s Operation/Reference Guide for information on learning a device’s IR  
commands.  
Audio Connectors:  
• Black RCA female connector - Digital audio  
• White RCA female connector - Analog audio Left  
• Red RCA female connector - Analog audio Right  
AUDIO Connectors  
The UDM-RX02 provides standard Audio RCA output connectors for S/PDIF for digital  
audio, and LEFT/RIGHT for analog audio output (FIG. 2).  
Video Connectors:  
• Yellow RCA female connector - CVBS (supports  
composite video)  
• S-Video - S-video female connector  
• VGA - HD15 female connector (supports VGA video)  
• Green RCA female connector - Component output: Y  
• Blue RCA female connector - Component output: Pb  
• Red RCA female connector - Component output: Pr  
VIDEO Connectors  
VGA Input at Display Device  
1.  
2.  
3.  
Attach one end of the VGA cable to the VGA connector on the UDM-RX02.  
Run the other end to the VGA connector on the display device. Connect firmly.  
If appropriate connect audio to the audio connectors on the UDM-RX02.  
Note: Ensure the UDM Hub port the RX02 is attached to is configured correctly  
within the Hub’s configuration software. Also ensure the correct Audio Type  
(Analog L/R, S/PDIF, or None) is selected for the relevant input.  
Operating Environment: • 35°F - 95°F (5°C - 35°C)  
• Max. relative humidity - 85% (non-condensing)  
Dimensions (HWD):  
Weight:  
1" x 8 15/16” x 3 3/8” (25 mm x 227 mm x 85 mm)  
1.45 lb. (658 g)  
Composite Input at Display Device  
1.  
2.  
3.  
Attach the composite cable (normally yellow) to the CVBS connector on the  
UDM-RX02.  
Run the other end of the composite cable to the Composite connector (normally  
yellow) on the display device. Connect firmly.  
Certifications:  
• CE  
• FCC part 15 Class A  
Other AMX Equipment: • RS232 DB9/RJ12 Connection Cable (FG-RS01)  
If appropriate connect audio to the audio connectors on the UDM-RX02.  
• UDM-RC02 Multi-Format IR Remote Control  
(FG-UDM-RC02)  
SVideo Input at Display Device  
• IR01 IR Emitter Module (FG-IR01)  
1.  
2.  
Attach the SVideo cable to the 4-pin S Video connector on the UDM-RX02.  
Run the other end of the SVideo cable to the SVideo connector on the display  
device. Connect firmly.  
• IR03 External IR Receiver Module (FG-IR03)  
• UDM-PS 24VDC, 750mA Power Supply (FG-UDM-PS)  
3.  
If appropriate connect audio to the audio connectors on the UDM-RX02.  
 

3Com Switch 3C16980 User Manual
Acer Laptop 290E User Manual
ADTRAN Heart Rate Monitor 1204002L2 User Manual
American Dryer Corp Clothes Dryer AD 235D User Manual
AMX Stereo Amplifier DAS LLC User Manual
Ativa Clock E PO 244 User Manual
Avenview Switch KVM C5 Series User Manual
Avital Automobile Alarm 3000 User Manual
Axis Communications Security Camera 209FD FD R User Manual
Eureka Tents Tent Grand Manan Tour User Manual